EVT12S‑10FT Black 10‑foot 12"×12" matte black box truss section with end‑plate bolt connection

EVT12S-10FT Black

Original price was: $1,300.00.Current price is: $979.00.

EVT12S-10FT Black — 10-Foot Black Truss Section – 12″ x 12″ Heavy-Duty Square Aluminum End-Plate Truss (Matte Black)

Dimensions & Specs
Overall Length: 10.0 ft (3.04 m)
Overall Width: 12 in (304.8 mm)
Type: Heavy-Duty Square Aluminum End-Plate Truss

Construction
Material Type: Aluminum Alloy EN AW-6061 T6
Main Tubing: 1.96 in (50 mm) OD / 0.11 in (3 mm) Wall Thickness
Brace Tubing: 0.98 in (25 mm) / 0.11 in (3 mm) Wall Thickness
Connection Type: End-Plated Nut and Bolt (Heavy-Duty Bolted Truss)

Finish & Features
Surface: Matte Black Powder Coat Finish
Certification: TUV Certified
Included: 4x Grade 8 Bolts, Nuts, and Washers
Weight: 59 lb (26.76 kg)

In stock

SKU: EVT12S-10FT-Black Category:

EVT12S System Knowledge Center

10 Ft Black Square Box Truss End Plate Section.
A 120 Inch Straight Section for End-Plate Box Truss Systems.

The EVT12S-10FT-Black is a 120-inch matte black aluminum straight section for standard 12-inch end-plate box truss systems. It suits long straight runs and tall frames where a single ten-foot black member is specified. Allowable loading depends on the complete system, including span, supports, connections, orientation, and applied loads.

Product Facts

Model / SKUEVT12S-10FT-Black
Product TypeBlack Square Aluminum End-Plate Truss Section
Overall Size12 x 12 x 120 in
Section Length120 in / 10 ft / 3048 mm
MaterialEN AW-6061-T6 Aluminum
FinishMatte Black Powder Coat
10 ftSection Length
12 × 12 inTruss Profile
50 mmMain Tubing
59 lbListed Weight
4-BoltEnd-Plate Connection

Product Overview

A 120-Inch Straight Section for End-Plate Box Truss Systems.

This ten-foot component uses an end-plated nut-and-bolt connection. Listed construction includes EN AW-6061-T6 aluminum, 50 mm main tubing, 25 mm diagonal brace tubing, and a matte black powder coat finish. Evaluate all loading and connection requirements at the completed-system level.

Matte Black Powder Coat
Listed matte black powder coat finish.
Diagonal Brace Tubing
Listed as 0.98 in / 25 mm OD with a 0.11 in / 3 mm wall.
Main Chord Tubing
Listed as 1.96 in / 50 mm OD with a 0.11 in / 3 mm wall.
End-Plate Connection
Listed end-plated nut-and-bolt connection format.

Application Uses

For End-Plate Truss Systems Using A 120-Inch Black Straight.

This 120-inch matte black section may be specified within completed end-plate box truss systems for staging, presentation, runway, production, and rental applications. Vertical or freestanding configurations require a project-specific static calculation and engineer review. Confirm span, supports, connections, orientation, attachment points, environmental conditions, and applied loads before use.

Concert and Festival Staging
For completed end-plate truss systems in stage productions that specify matte black components.
Corporate Keynote Stages
For presentation structures built from standard 12-inch end-plated truss.
Fashion and Runway Productions
For project-specific stage and display frames where a black straight section is specified.
Cinema and Streaming Sets
For production environments where a long black straight section is specified within the completed system.
Black-Finish Rental Packages
For rental inventories that include 120-inch black straight sections.

Included Hardware

Listed Hardware for One Four-Point Connection.

The product data lists four Grade 8 bolts, four nuts, and four washers. Confirm fastener requirements at every actual joint, including bolt length, condition, engagement, and the applicable manufacturer tightening procedure.

4 Grade 8 Bolts
Listed for the four-point end-plate connection.
4 Nuts
Listed with the supplied bolts.
4 Washers
Included in the listed hardware set.
Hardware Finish
Hardware finish may vary; standard zinc or galvanized is typically supplied unless otherwise specified.

Technical Reference

EVT12S-10FT-Black Truss Section Specifications.

Identification

Product Details

Model / SKUEVT12S-10FT-Black
BrandEvolve Truss
Product TypeBlack 10 Foot Square Aluminum End-Plate Truss Section
Warranty1-Year Limited Warranty Against Manufacturing Defects

Dimensions

Overall Size

Width12 in / 304.8 mm
Height12 in / 304.8 mm
Depth / Length120 in / 10 ft / 3048 mm
Weight59 lb / 26.76 kg

Material and Tubing

Construction

MaterialAluminum Alloy EN AW-6061-T6
Main Tubing1.96 in / 50 mm OD, 0.11 in / 3 mm Wall
Brace Tubing0.98 in / 25 mm OD, 0.11 in / 3 mm Wall
FinishMatte Black Powder Coat

Connection Context

System Interface

Connection TypeEnd-Plated Nut and Bolt
Included Hardware4 Grade 8 Bolts, Nuts, and Washers
CompatibilityStandard 12-Inch End-Plated Truss Systems
CertificationTÜV Certified
Fit NoticeExact fit with other systems is not guaranteed

System Compatibility

For Standard 12-Inch End-Plated Truss Systems. Verify Every Connection.

This section is identified for standard 12-inch end-plated truss systems. Exact fit with other systems is not guaranteed. Before combining components, verify end-plate dimensions and thickness, bolt-hole positions, chord alignment, hardware, fastener engagement, and completed-joint seating.

System Match
Confirm the system uses a standard 12-inch end-plated format.
End Plates
Compare plate dimensions and bolt-hole positions.
Hardware
Confirm appropriate fasteners and engagement.
Completed Joint
Inspect alignment and full seating before use.

Assembly Overview

Align the End Plates. Install and Check All Four Fasteners.

Assembly should be performed by personnel qualified for the truss system in accordance with applicable manufacturer requirements. This outline provides neither torque values nor installation approval.

01 — Inspect
Check tubing, diagonal bracing, welds, plates, holes, finish, and hardware for damage.
02 — Align
Bring compatible end plates together without forcing distorted parts.
03 — Install Hardware
Fit specified fasteners at all four locations with adequate engagement.
04 — Tighten
Follow the applicable manufacturer fastener procedure.
05 — Check Seating
Confirm required hardware and full plate seating.
06 — Inspect Before Service
Review the completed truss system and supports before loading.

Engineering Reference

Load-Span Reference for Completed EVT12S Truss Runs.

All truss loading calculations are based on a completed compatible 12 x 12 aluminum-truss run supported or suspended at both ends, under one stated static-load alternative. The values below do not rate an individual straight section, plate, or ten-foot truss segment. A section changes the overall length and adds bolted joints; it does not increase the completed system’s allowable capacity.

Allowable loading reference for the documented 12 x 12 aluminum-truss analysis.
Load CaseUnit10 ft
3.05 m		20 ft
6.11 m		30 ft
9.14 m		40 ft
12.23 m
Uniformly Distributed Loadlb/ft4721156031
Deflectionin0.210.651.632.68
Center Point Loadlb2,7101,206580272
Deflectionin0.200.561.312.04
Third Point Loadslb each1,744888600442
Deflectionin0.320.681.482.62
Quarter Point Loadslb each1,110633428308
Deflectionin0.330.681.542.54
Load cases: CPL — one center load · TPL — two equal third-point loads · QPL — two equal quarter-point loads · UDL — load distributed over the complete span
Load-Span Assumptions and Project Review

Table assumptions: The reference evaluates unbraced truss configured as a simply supported beam. The primary analyzed spans were 10 ft, 20 ft, 30 ft, and 40 ft. If CPL, TPL, or QPL loading occurs at a truss connection, a minimum of two chords is assumed to support the vertical load.

Not included: Shock loads, dynamic loads, and resultant horizontal rigging forces, including forces from bridles or baskets. UDL applies only when the load is evenly distributed across the entire span. Published load cases are alternatives and are not additive.

Licensed structural-engineer review is required for every truss system. These values are general planning reference only and do not approve or rate an individual straight section, a completed lighting plot, a ground-support structure, a goal post, a tower, a start/finish arch, a suspended configuration, an outdoor installation, a mixed-component build, or any other assembled truss system. Confirm the complete configuration, supports, connections, span, applied loads, attachment points, rigging, ballast or anchorage, environmental conditions, and applicable code requirements with a licensed structural engineer before use.

Current documentation: Product specifications, included hardware, compatibility information, and availability are subject to change. Verify current product drawings, manufacturer instructions, connection hardware, and applicable engineering information before ordering, assembling, or using this product.

Safety and Engineering

A Truss Section Adds Length. It Does Not Increase Truss Capacity.

Allowable loading depends on the complete truss system, including span, supports, orientation, joints, suspension method, and applied loads. Suspended, load-bearing, dynamic-load, and complex applications require qualified structural or entertainment-rigging review. No stand-alone capacity value or torque value is provided here.

Inspect the truss section, diagonal braces, welds, plates, bolt holes, hardware, and connected truss before every use.
Remove any component with cracks, bends, elongated holes, plate deformation, damaged welds, or substantial finish damage from service.
Install and tighten all required fasteners using the applicable manufacturer procedure.
Do not support loads directly from connection points without approval for the complete truss system.
Verify connection interfaces and completed-system suitability before combining different systems.
Have a competent person perform a documented inspection at least annually and remove unsafe parts from service.

Truss Section Questions

EVT12S-10FT-Black Frequently Asked Questions.

What construction details are listed?

The product data lists EN AW-6061-T6 aluminum, 50 mm main tubing, 25 mm diagonal brace tubing, and a matte black powder coat finish.

What hardware is listed?

The listed product data identifies four Grade 8 bolts, four nuts, and four washers. Hardware finish may vary.

What is the listed weight?

The listed weight is 59 lb / 26.76 kg.

Can it be used vertically?

Vertical use requires a specific static calculation and structural-engineer review, including wind and transverse forces for the completed structure.

Does it have a separate load capacity?

No stand-alone capacity value is provided here. Allowable loading depends on the complete system and its support and loading conditions.

Need an EVT12S Ten Foot Black Truss Section?

Contact us for truss section selection, listed compatibility information, product documentation, and quantity-quote support.

Contact UsRequest a Quote

Structural Solutions, Unmatched Innovation