EVT12S-60DCA

EVT12S-60DCA

Original price was: $990.00.Current price is: $750.00.

EVT12S-60DCA — 60 Degree Corner Block – 12″ x 12″ Square Box Truss

Dimensions & Specs
Overall Length: 14.66 in (372.39 mm)
Overall Width: 12 in (304.8 mm)
Angle: 60 Degrees
Type: Heavy-Duty Square Aluminum Truss Corner – Fixed Angle End-Plate

Construction
Material Type: Aluminum Alloy EN AW-6061 T6
Main Tubing: 1.96 in (50 mm) OD / 0.11 in (3 mm) Wall Thickness
Brace Tubing: 0.98 in (25 mm) / 0.11 in (3 mm) Wall Thickness
Connection Type: End-Plated Nut and Bolt (Heavy-Duty Bolted Truss)

Finish & Features
Surface: Aluminum Brush Finish
Certification: TUV Certified
Included: 4x Grade 8 Bolts, Nuts, and Washers
Weight: 17.80 lb (8.07 kg)

In stock

SKU: EVT12S-60DCA Category:

EVT12S System Knowledge Center

60 Degree Corner Angle for 12 x 12 Square Box Truss.
A Fixed-Angle Component for End-Plate Box Truss Systems.

The EVT12S-60DCA is a 60-degree corner angle for standard 12 x 12 end-plate box truss systems. This fixed-angle component changes the direction of a truss run within the completed system. Allowable loading depends on the complete system, including span, supports, connections, orientation, and applied loads.

Product Facts

Model / SKUEVT12S-60DCA
Product Type60 Degree Fixed-Angle Corner
Truss Size12 x 12 in
MaterialEN AW-6061-T6 Aluminum
FinishBrushed Aluminum
Estimated Weight17.80 lb / 8.07 kg
60°Fixed Angle
12 inTruss Size
17.80 lbEstimated Weight
EN AW-6061-T6Material
4-BoltEnd-Plate Connection

Product Overview

A Fixed 60-Degree Corner Angle for 12 x 12 End-Plate Box Truss.

This component changes the direction of compatible end-plated 12-inch box truss at a fixed 60-degree angle. Construction is EN AW-6061-T6 aluminum with a brushed aluminum finish. Evaluate all loading and connection requirements at the completed-system level.

60-Degree Angle
Fixed-angle corner format.
Brushed Aluminum Finish
Brushed aluminum surface finish.
EN AW-6061-T6 Aluminum
Aluminum alloy construction.
End-Plate Connection
End-plated nut-and-bolt connection format.

Application Uses

For End-Plate Truss Systems Needing A Fixed 60-Degree Change of Direction.

This 60-degree corner angle may be specified within completed end-plate box truss systems for display, stage, exhibit, and scenic applications. Angled configurations change load paths and require project-specific structural-engineer review. Confirm the complete configuration, supports, connections, orientation, attachment points, environmental conditions, and applied loads before use.

Segmented and Hexagonal Frames
For completed truss frames using repeated fixed-angle corners.
Angled Presentation Structures
For project-specific presentation and display structures subject to completed-system review.
Angled Display Perimeters
For exhibit frames that specify a series of 60-degree corners.
Stage Front Transitions
For stage structures that change direction using end-plated truss components.
Angular Scenic Frames
For scenic frames using specified fixed-angle corners.

Included Hardware

Hardware for One Four-Point Connection.

The product data specifies four Grade 8 bolts, four nuts, and four washers. Confirm fastener requirements at every actual joint, including bolt length, condition, engagement, and the applicable manufacturer tightening procedure.

4 Grade 8 Bolts
Supplied for the end-plate connection.
4 Nuts
Supplied with the bolts.
4 Washers
Included in the hardware set.
Connection Count
Account for hardware at each joint in the complete system.

Technical Reference

EVT12S-60DCA Fixed-Angle Corner Specifications.

Identification

Product Details

Model / SKUEVT12S-60DCA
BrandEvolve Truss
Product Type60 Degree Fixed-Angle Corner
Warranty1-Year Limited Warranty Against Manufacturing Defects

Dimensions

Overall Dimensions

Overall Length (X)12.00 in / 304.80 mm
Overall Depth (Y)14.66 in / 372.39 mm
Overall Height (Z)15.00 in / 381.01 mm
Estimated Weight17.80 lb / 8.07 kg
Fixed Angle60 Degrees
Nominal Truss Size12 x 12 in / 304.8 x 304.8 mm

Material and Tubing

Construction

MaterialAluminum Alloy EN AW-6061-T6
Main Tubing1.97 in / 50 mm OD, 0.12 in / 3 mm Wall
Brace Tubing0.98 in / 25 mm OD, 0.12 in / 3 mm Wall
FinishBrushed Aluminum

Connection Context

System Interface

Connection TypeEnd-Plated Nut and Bolt
Included Hardware4 Grade 8 Bolts, Nuts, and Washers
CompatibilityStandard 12-Inch End-Plated Truss Systems
CertificationTÜV Certified
Fit NoticeExact fit with other systems is not guaranteed

System Compatibility

For Standard 12-Inch End-Plated Truss Systems. Verify Every Connection.

This corner angle is identified for standard 12-inch end-plated truss systems. Exact fit with other systems is not guaranteed. Before combining components, verify end-plate dimensions and thickness, bolt-hole positions, chord alignment, hardware, fastener engagement, and completed-joint seating.

System Match
Confirm the system uses a standard 12-inch end-plated format.
End Plates
Compare plate dimensions and bolt-hole positions.
Hardware
Confirm appropriate fasteners and engagement.
Completed Joint
Inspect alignment and full seating before use.

Assembly Overview

Align the End Plates. Install and Check All Four Fasteners.

Assembly should be performed by personnel qualified for the truss system in accordance with applicable manufacturer requirements. This outline provides neither torque values nor installation approval.

01 — Inspect
Check tubing, braces, welds, plates, holes, finish, and hardware for damage.
02 — Orient
Confirm the fixed-angle orientation within the completed system before assembly.
03 — Align
Bring compatible end plates together without forcing distorted parts.
04 — Install Hardware
Fit specified fasteners at all four locations with adequate engagement.
05 — Tighten
Follow the applicable manufacturer fastener procedure.
06 — Inspect Before Service
Review the completed truss system and supports before loading.

Safety and Engineering

A Fixed-Angle Corner Changes Direction. It Does Not Establish System Capacity.

Allowable loading depends on the complete truss system, including span, supports, orientation, joints, suspension method, and applied loads. Suspended, load-bearing, dynamic-load, and angled applications require qualified structural or entertainment-rigging review. No stand-alone capacity value or torque value is provided here.

Inspect the corner angle, braces, welds, plates, bolt holes, hardware, and connected truss before every use.
Remove any component with cracks, bends, elongated holes, plate deformation, damaged welds, or substantial finish damage from service.
Install and tighten all required fasteners using the applicable manufacturer procedure.
Do not support loads directly from corner connection points without approval for the complete truss system.
Angled connections change load paths; obtain structural-engineer review for every completed truss system.
Verify connection interfaces and completed-system suitability before combining different systems.
Have a competent person perform a recorded inspection at least annually and remove unsafe parts from service.

Corner Angle Questions

EVT12S-60DCA Frequently Asked Questions.

What angle does it provide?

The product has a fixed 60-degree angle.

What are the overall dimensions and weight?

The overall length (X) is 12.00 in / 304.80 mm, the overall depth (Y) is 14.66 in / 372.39 mm, and the overall height (Z) is 15.00 in / 381.01 mm. The estimated weight is 17.80 lb / 8.07 kg.

What construction details apply?

Construction is EN AW-6061-T6 aluminum with 50 mm main tubing, 25 mm brace tubing, and a brushed aluminum finish.

What hardware is included?

The hardware set is four Grade 8 bolts, four nuts, and four washers.

Does it have a separate load capacity?

No stand-alone capacity value is provided here. Allowable loading depends on the complete system and its support and loading conditions.

Need an EVT12S 60 Degree Corner Angle?

Contact us for corner-angle selection, compatibility information, product information, and quantity-quote support.

Contact UsRequest a Quote

Structural Solutions, Unmatched Innovation